Aerospace Engineering Theses and Dissertations
Permanent URI for this collectionhttp://hdl.handle.net/1903/2737
Browse
159 results
Search Results
Item Experimental Evaluation of Circulation Control Aerodynamics on a Cylindrical Body(1987) Ngo, Hieu Thien; Chopra, Inderjit; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, MD)In this study, an experimental investigation is conducted on a two-dimensional circulation control cylinder with blowing taking place from a single spanwise slot to determine its aerodynamic characteristics. The results include detailed pressure distributions (both chordwise and spanwise) for a range of momentum coefficients and slot locations. The measured results showed that the lift coefficients up to 4.8 were produced at momentum coefficients of 0.14 in a turbulent flow condition. The experimental results of lift coeffficients Were correlated satisfactorily with analytical results. The surface flow patterns were observed using the oil and smoke techniques. Also flow field surveys of the model Were obtained using total pressure, yaw and pitch probes. A color video display technique was used to present the results of the flow field surveys. Based on this evidence, a flow field model of the circulation control cylinder is presented.Item An Expert System for Helicopter Conceptual Design(1987) Babuska, Vit; Fabunmi, James A.; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md)The objective of this thesis is to demonstrate the applicability of expert systems in helicopter conceptual design by developing an expert assistant which aids the engineer in defining a feasible design configuration. The expert assistant combines some experiential knowledge of the design engineer with a typical conceptual design algorithm to guide the engineer to a reasonable baseline design. The expert assistant was developed on a personal computer using the expert system shell INSIGHT2+®. The design algorithm employed is SSPl, a helicopter weight and sizing program developed at the US Army Applied Technologies Laboratory. A set of heuristic rules was developed which attempts to simulate the thinking of an expert design engineer using SSP1 for helicopter conceptual design. The result, a Prototype expert assistant which aids an engineer in the conceptual design phase, demonstrates the feasibility of expert systems in helicopter design.Item Navier Stokes Solutions for Chemical Laser Flows: Steady and Unsteady Flows(1979) Kothari, Ajay Prasannajit; Anderson, John D. Jr; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md)This work consists of an overall effort to apply a detailed and accurate computational fluid dynamic technique to the solution of practical high energy laser flows. In particular, a third generation of super sonic diffusion chemical laser analysis is introduced, namely, the complete solution of the Navier-Stokes equations for the laminar, super sonic mixing flow fields fully coupled with chemical kinetics for both the hot and cold reactions for HF. Multicomponent diffusion is treated in a detailed fashion. Solutions are obtained, firstly, for "cold flows", where the effects of chemical reactions and vibrational relaxation are not included. Although such a situation is purely artificial, the results do isolate some of the fluid dynamic aspects of chemical laser flows, and provide a set of data to be compared later with hot flow calculations. A set of numerical experiments using four different time dependent finite difference schemes show that relatively minor changes in the differencing procedure can lead to major variations in the results. A modification of the well-known Maccormack approach appears to be the best suited for mixing flows associated with chemical lasers. A comparison is next made between cold flows (with fully coupled chemical kinetics). the results show that temperature distributions are affected the most and velocity distributions the least by chemical energy heat release. The results have an impact on the interpretation of cold flow aerodynamic experiments in the laboratory, and their proper extrapolation to the real chemical laser flows. also, comparisons between the present Navier Stokes results and other, more approximate, existing calculations are made. Gradients are calculated as a natural part of the Navier Stokes solutions. Results are given for steady flows with large pressure gradients where advantages of the Navier Stokes solutions are delineated. In addition, the effect of unsteady fluctuations intentionally introduced at the cavity inlet are studied. Specifically, sinusoidal fluctuations in one stream and then both streams (primary and secondary) in various quantities e.g. pressure, density, u velocity and v velocity were simulated. Of these, the oscillations in v velocity with approximate frequency and amplitude produced a remarkable improvement in mixing. Such unsteady fluctuations also yielded peak laser gain which were larger by almost a factor of two compared to the steady case. the flow at which the upstream boundary has so far, in the above mentioned cases been assumed to be uniform with real effects like Boundary Layer and Base Flow having been neglected. For comparison purposes these effects are next included. the boundary layer profile and velocity at the inlet is shown to feed production of gain substantially. Base flow calculations were attempted but were not successfulItem The Influence of Variable Flow Velocity on Unsteady Airfoil Behavior(1991) van der Wall, Berend G.; Leishman, J. Gordon; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md)The importance of unsteady aerodynamics for prediction of rotor dynamics is unquestioned today. The purpose of unsteady aerodynamic models is to represent the effect of unsteady airfoil motion on the lift, moment and drag characteristics of a blade section. This includes unsteady motion (arbitrary motion) of the airfoil in angle of attack (pitch) and vertical movement (plunge), as well as the effects of an airfoil traveling through a vertical gust field. However, the additional degrees of freedom, namely the fore-aft motion and the unsteady freestream variations commonly are acknowledged, but neglected in virtually all analyses. Since the effect of unsteady freestream results in a stretching and compressing of the shed wake vorticity distribution behind an airfoil, it will have an effect on the airfoil characteristics. The subject of this thesis is to provide a review of the analytic and experimental work done in the area of unsteady freestream and unsteady fore-aft motion, to clarify the limits of the various theories, and to show the differences between them. This will be limited to the attached flow regime since all theories are based on the small disturbance assumption in incompressible flow. As far as possible the theories are compared with experimental data, however most of the available experimental data are confined to stalled flow conditions and are not useful here. In addition to the theories, a semiempirical mathematical model will be used based on the aerodynamics of indicial functions. The purpose is to show the differences of using the theories of unsteady airfoil motion in a constant flow, and those accounting for unsteady freestream flow. This will help to justify whether it is necessary to include the unsteady freestream effect in comprehensive rotor codes. Finally, a generalisation of Isaacs unsteady aerodynamic theory for an airfoil undergoing a frequency spectra in pitch and plunge in a freestream oscillating with the fundamental frequency is presented here for the first time. Therein the axis of rotation of the airfoil is a free parameter.Item An Experimental Investigation of the Effects of Leading Edge Modification on the Post-Stall Characteristics of an NACA 0015 Wing(1979) Saini, Jugal Kishore; Jones, Everett; Winkelmann, Allen E.; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, MD)The effects of leading edge modifications on the stalling characteristics of an NACA 0015 panel wing model were investigated in a series of low speed wind tunnel tests. The modification typically consisted of adding a 14% Clark Y glove onto a portion of the leading edge. Six-component balance data, pressure distribution measurements and oil flow visualization tests were completed at a Reynolds number based on chord of 2.0 x 10^6 for increasing and decreasing angles of attack from 0° to 50°. The leading edge modifications produce stabilizing vortices at stall and beyond. These vortices have the effect of fixing the stall pattern of the wing such that various portions of the wing upper surface stall nearly symmetrically. This results in a higher lift on the modified wing as compared to the lift on the unmodified wing in the post-stall region. The lift curve slope of the modified and unmodified wings remained essentially constant at 0.071 per degree. Two lift-coefficient peaks were obtained for the baseline NACA 0015 wing at angles of attack of 17° and 30°. The twin-peak behavior of the lift curve was also observed on the modified wings. The drag coefficient obtained with several modified configurations was smaller than the drag coefficient of the baseline NACA 0015 wing in the pre-stall region. Also a smaller center of pressure shift with angle of attack was observed with several modified configurations. Considering a smoother variation of lift, pitching moment, rolling moment at stall and a smaller drag and center of pressure movement to be desired criteria, the best configuration tested consisted of placing the glove on the entire leading edge except for a gap at 25% to 50% of the semispan.Item Transient Dynamics of Helicopter Rotor Wakes Using a Time-Accurate Free-Vortex Method(2001) Bhagwat, Mahendra J.; Leishman, J. Gordon; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md)A second-order accurate predictor-corrector type algorithm has been developed to obtain a time-accurate solution of the vortical wake generated by a helicopter rotor. The rotor blade flapping solution was fully integrated with the wake geometry solution using the same time-marching algorithm. The analysis was used to predict the locations of wake vortex filaments under transient flight conditions, where the rotor wake may not be periodic at the rotational frequency. Applications of this analysis include prediction of the rotor induced velocity field and blade airloads during transient flight and maneuvers. The stability of the rotor wake structure is important from the perspective of free-vortex wake models. The wake stability was examined using a linearized stability analysis, and the rotor wake was shown to be physically unstable. Therefore, the stability of the numerical algorithm is an important consideration in developing robust wake methodologies. Both the stability and accuracy of the numerical wake solutions algorithms was rigorously examined. The straight-line vortex segmentation used in the present analysis was shown to be second-order accurate. The overall numerical solution was also demonstrated to converge with a second-order accuracy. A technique for increasing the order of accuracy for high resolution solutions is also described. Along with a formal (mathematical) verification of solution accuracy, the numerical solution for the rotor wake problem was compared with experimental results for both steady-state and transient operating conditions. The steady-state wake model was shown to give good predictions of rotor wake geometry, induced inflow distribution as well as performance trends. Under transient conditions, such as those following a pitch input during a maneuver, the time-accurate wake model was shown to correctly model the dynamic response of rotor wake. In axial descent passing through the vortex ring state, the present analysis was shown to properly model the associated power losses as shown by experimental results. The present analysis was also shown to give improved predictions of wake distortions during simulated maneuvering flight with various imposed angular rates of the rotor.Item MATHEMATICAL MODEL OF ADAPTIVE MOTOR CONTROL(1999) Kosha, Makiko; Sanner, Robert M.; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md)An adaptive control law incorporating a biologically inspired neural networks for robot control is used as a mathematical model of human motor control and the motor control adaptation. Modeling human motor control strategy is made difficult due to the redundancies in the human motor control system. This control model is able to overcome the difficulties of the human motor control modelling, and include the learning capability of the motor control strategy which was omitted in human motor control studies until now. By adaptively piecing together a collection of elementary computational elements, the proposed model develops complex internal models which are used to compensate for the effects of externally imposed forces or changes in the physical properties of the system. In order to examine the form of human motor control adaptation in detail, a computer simulation was developed with a two dimensional model of the human arm which utilized the proposed adaptive motor control model. The simulation result show that the model is able to capture the characteristics of the motor control adaptation seen in human experiments reported by [14], [46]. For cont inuation of this research, an experimental apparatus was designed and built for the human motor control study. This apparatus is a cable driven, two-dimensional manipulator which is used to apply specified disturbance forces to the human arm. The preliminary experiment conducted with this test apparatus show a strong correlation to the simulation data and other experimental data reported on human reaching motions.Item Numerical Solutions for Two- and Three-Dimensional Non-Reacting Flowfields in an Internal Combustion Engine(1977) Griffin, Michael Douglas; Anderson, John D. Jr; Jones, Everett; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md)The numerical solution for the flowfield established in a spark- ignition internal combustion engine during the four-stroke (intake, compression, power, exhaust) cycle is considered. Only fluid-dynamic effects are treated with combustion simulated by constant- volume heat addition near top-dead-center on the compression stroke. The working fluid is assumed to be air of constant specific heat, with both viscous and inviscid models considered. Two- and three-dimensional engine models are examined, with the three-dimensional models including both rectangular and cylindrical geometries. The difficulties associated with obtaining numerical solutions in cylindrical coordinates for three-dimensional non-axisymmetric problems when the centerline is included in the region of interest are discussed. A new method which avoids the coordinate- singularity problems associated with such cases is presented and used to obtain the first known four-stroke inviscid-flow solution for a three- dimensional cylindrical engine model. Similar results are presented for a three-dimensional rectangular model, and for the first known two-dimensional four-stroke calculation for a viscous fluid. The inviscid three-dimensional results are compared with each other and with previously obtained two-dimensional inviscid-flow calculations. The use of two-dimensional models is found to be justified for the non- reacting flowfields considered, since the results obtained from a two-dimensional calculation in the valve plane are apparently not strongly dependent on the flowfield perpendicular to the valve plane. It is found that significant flowfields do exist in all I.C. engine models considered. It is shown that the unit-cell-Reynolds-number criterion limits viscous flow calculations to Reynolds numbers of approximately one ten-thousandth the realistic value, and that this produces flowfields which are strongly piston-dominated. In contrast, inviscid results show marked circulatory patterns, which are more realistic. The velocity patterns which develop in the three-dimensional cylindrical engine model are shown to exhibit a marked swirl in planes parallel and perpendicular to the cylinder axis.Item Dynamics of a Helicopter-Slung Load System(1980) Sampath, Prasad; Barlow, Jewel B.; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md)Stability of a tandem rotor helicopter (347/HLH) carrying a slung cargo container has been investigated. Lagrange equations were used to write the equations of motion. The cables of the sling were modeled as massless rigid extensible rods, which collapse under compressive loads. Extensibility was provided by considering the rods as linear spring with viscous damping. Aerodynamics of the cable were neglected. Tabulated static aerodynamic data were considered for the helicopter as well as the load. The equations were divided into two sets, one representing the towing vehicle (referred to as Subsystem 1) and the other representing the slung load (referred to as Subsystem 2). Subsystem 2 corresponds to a wind tunnel model of a slung load.Item RBCC Engine-Airframe Integration on an Osculating Cone Waverider Vehicle(2001) O'Brien, Timothy F.; Lewis, Mark J.; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md)An analytical vehicle study is performed that integrates a rocket-based combined cycle engine with an osculating cones waverider-based fuselage. The integration of the two concepts brings about an interesting design challenge: predicting the aerodynamic performance of a high-speed fuselage design across the full range of Mach numbers from take-off to orbit that a rocket-based combined-cycle engine will operate. The aerodynamic performance of this class of vehicles is analyzed for on- and off-design Mach numbers and angles of attack. Analytical aerodynamic models are developed for the off-design behavior of both the fuselage of the vehicle and the engine. These models arc combined to predict the powered performance of this class of vehicle along a trajectory. The models developed arc rapid enough that they may be applied to initial design studies, optimization algorithms, or trajectory analyses. The aerodynamic model for the fuselage is based on the tangent-wedge, tangent-cone, and shock-expansion theories for hypersonic flow, and the linearized, small perturbation, velocity potential equations for supersonic and transonic flow. Each model is validated with numerical solutions for an example Mach 12 vehicle design. The results show an accurate prediction of the trends in lift and drag of the vehicle fuselage across a range of Mach numbers between 0.4 and 15. The aerodynamic engine model is based on Prandtl-Meyer flow and the oblique shock relations for the internal compression system, and quasi-one dimensional flow (including finite-rate chemistry) for the combustor flowfield. The strut-based compression model is validated with numerical solutions for a range of Mach numbers between 2.5 and 6. The combustor flowfield model is validated by comparison to two experimental hydrogen-fueled scramjet engines. The results showed that this class of geometry generates very little lift at low speeds (below Mach 3) and will require lift augmentation. The transonic drag rise is modeled analytically and numerically, with maximum inviscid drag coefficient occurring at Mach 1.2. Engine integration has a large effect on off-design behavior, including maximum lift-to-drag ratio and zero lift angle of attack.