UMD Theses and Dissertations
Permanent URI for this collectionhttp://hdl.handle.net/1903/3
New submissions to the thesis/dissertation collections are added automatically as they are received from the Graduate School. Currently, the Graduate School deposits all theses and dissertations from a given semester after the official graduation date. This means that there may be up to a 4 month delay in the appearance of a given thesis/dissertation in DRUM.
More information is available at Theses and Dissertations at University of Maryland Libraries.
Browse
4 results
Search Results
Item HIGH PERFORMANCE NANOPHOTONIC CAVITIES AND INTERCONNECTS FOR OPTICAL PARAMETRIC OSCILLATORS AND QUANTUM EMITTERS(2024) Perez, Edgar; Srinivasan, Kartik; Hafezi, Mohammad; Physics; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)Integrated photonic devices like photonic crystals, microring resonators, and quantum emitters produce useful states of light, like solitons or single photons, through carefully engineered light-matter interactions. However, practical devices demand advanced integration techniques to meet the needs of cutting-edge technologies. High performance nanophotonic cavities and interconnects present opportunities to solve outstanding issues in the integration of nanophotonic devices. In this dissertation I develop three core tools required for the comprehensive integration of quantum emitters: wavelength-flexible excitation sources with sufficient pump power to drive down stream systems, photonic interconnects to spatially link the excitation sources to emitters, and cavities that can Purcell enhance quantum emitters without sacrificing other performance metrics. To create wavelength-flexible excitation sources, a high-performance χ(3)microring Optical Parametric Oscillator (OPO) is realized in silicon nitride. Microring OPOs are nonlinear frequency conversion devices that can extend the range of a high-quality on-chip (or off-chip) laser source to new wavelengths. However, parasitic effects normally limit the output power and conversion efficiency of χ(3)microring OPOs. This issue is resolved by using a microring geometry with strongly normal dispersion to suppress parasitic processes and multiple spatial mode families to satisfy the phase and frequency matching conditions. Our OPO achieves world-class performance with a conversion efficiency of up to 29% and an on-chip output power of over 18 mW. To create photonic interconnects, Direct Laser Writing (DLW) is used to fabricate 3-dimensional (3D) nanophotonic devices that can couple light into and out of photonic chips. In particular, polymer microlenses of 20 μm diameter are fabricated on the facet of photonic chips that increase the tolerance of the chips to misaligned input fibers by a factor of approximately 4. To do so, we develop the on-axis DLW method for photonic chips, which avoids the so-called "shadowing" effect and uses barcodes for automated alignment with machine vision. DLW is also used to fabricate Polymer Nanowires (PNWs) with diameters smaller than 1 μm that can directly couple photons from quantum emitters into Gaussian-like optical modes. Comparing the same quantum emitter system before and after the fabrication of a PNW, a (3 ± 0.7)× increase in the fiber-coupled collection efficiency is measured in the system with the PNW. To refine the design of quantum emitter cavities, a toy model is used to understand the underlying mechanisms that shape the emission profiles of Circular Bragg Gratings (CBGs). Insights from the toy model are used to guide the Bayesian optimization of high-performance CBG cavities suitable for coupling to single-mode fibers. I also demonstrate cavity designs with quality factors (Q) greater than 100000, which can be used in future experiments in cavity quantum electrodynamics or nonlinear optics. Finally, I show that these cavities can be optimized for extraction to a cladded PNW while producing a Purcell enhancement factor of 100 with efficient extraction into the fundamental PNW mode. The tools developed in this dissertation can be used to integrate individual quantum emitter systems or to build more complex systems, like quantum networks, that require the integration of multiple quantum emitters with multiple photonic devices.Item Hybridization and enhancement processes in quasi-two dimensional superconductors(2019) Raines, Zachary Mark; Galitski, Victor M; Physics; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)Superconductivity is a field with a great many branches and applications. In this dissertation, we focus on two specific processes in superconductors -- light-induced enhancement and hybridization of collective modes -- in two types of quasi-two dimensional materials -- either the loosely coupled planes of a layered superconductor or a superconducting thin film. Motivated by experiments in the cuprates that have seen evidence of a transient superconducting state upon optical excitation we study the effects of inter-plane tunneling on the competition between superconductivity and charge order. We find that an optical pump can suppress the charge order and simultaneously enhance superconductivity, due to the inherent competition between the two. Taking into account that the charge order empirically shows a broad peak in c-axis momentum, we consider a model of randomly oriented charge ordering domains and study how interlayer coupling affects the competition of this order with superconductivity. Also in the cuprates, several groups have reported observations of collective modes of the charge order present in underdoped cuprates. Motivated by these experiments, we study theoretically the oscillations of the order parameters, both in the case of pure charge order, and for charge order coexisting with superconductivity. Using a hot-spot approximation we find in the coexistence regime two Higgs modes arising from hybridization of the amplitude oscillations of the different order parameters. We explore the damping channels of these hybrid modes. As another means of enhancing superconductivity we consider coupling a two-dimensional superconducting film to the quantized electromagnetic modes of a microwave resonator cavity. We find that when the photon and quasiparticle systems are out of thermal equilibrium, a redistribution of quasiparticles into a more favorable non-equilibrium steady-state occurs, thereby enhancing superconductivity in the sample, a fluctuation analog of a phenomenon known as the Eliashberg effect. Finally, following the recent success of realizing exciton-polariton condensates in cavities, we examine the hybridization of cavity photons with two types of collective modes in superconductors. Enabled by the recently predicted and observed supercurrent-induced linear coupling between these excitations and light, we find that significant hybridization between the superconductor's collective modes and resonant cavity photons can occur.Item Variable Qubit-Qubit Coupling Via a Tunable LC Resonator(2018) Ballard, Cody James; Wellstood, Frederick C.; Lobb, Christopher J.; Physics; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)This dissertation examines the design, fabrication, and characterization of a superconducting lumped-element tunable LC resonator that is used to vary the coupling between two superconducting qubits. Some level of qubit-qubit coupling is needed to perform gating operations. However, with fixed coupling, single qubit operations become considerably more difficult due to dispersive shifts in their energy levels transitions that depend on the state of the other qubit. Ideally, one wants a system in which the qubit-qubit coupling can be turned off to allow for single qubit operations, and then turned back on to allow for multi-qubit gate operations. I present results on a device that has two fixed-frequency transmon qubits capacitively coupled to a tunable thin-film LC resonator. The resonator can be tuned in situ over a range of 4.14 GHz to 4.94 GHz by applying an external magnetic flux to two single-Josephson junction loops, which are incorporated into the resonator’s inductance. The qubits have 0-to-1 transition frequencies of 5.10 GHz and 4.74 GHz. To isolate the system and provide a means for reading out the state of the qubit readout, the device was mounted in a 3D Al microwave cavity with a TE101 mode resonance frequency of about 6.1 GHz. The flux-dependent transition frequencies of the system were measured and fit to results from a coupled Hamiltonian model. With the LC resonator tuned to its minimum resonance frequency, I observed a qubit-qubit dispersive shift of 2χ_qq≈ 0.1 MHz, which was less than the linewidth of the qubit transitions. This dispersive shift was sufficiently small to consider the coupling “off”, allowing single qubit operations. The qubit-qubit dispersive shift varied with the applied flux up to a maximum dispersive shift of 2χ_qq≈ 6 MHz. As a proof-of-principle, I present preliminary results on performing a CNOT gate operation on the qubits when the coupling was “on” with 2χ_qq≈ 4 MHz. This dissertation also includes observations of the temperature dependence of the relaxation time T1 of three Al/AlOx/Al transmons. We found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK. We found that this anomalous behavior was consistent with loss due to non-equilibrium quasiparticles in a transmon where one electrode in the tunnel junction had a smaller volume and slightly smaller superconducting energy gap than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with a smaller gap, leading to an increased density of quasiparticles at the junction and a corresponding decrease in the relaxation time. I present a model of this effect, use the model to extract the density of non-equilibrium quasiparticles in the device, and find the values of the two superconducting energy gaps.Item Analysis and Mitigation of Electromagnetic Noise in Resonant Cavities and Apertures(2004-08-10) Li, Lin; Ramahi, Omar M; Mechanical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)The trend of low voltage in electronics circuits and boards makes them vulnerable to electromagnetic interference (EMI). Furthermore, higher speed (clock rate) leads to faster switching which increases the potential for higher radiation from circuits and boards. These inevitable trends collectively compromise the electromagnetic compatibility of electronic systems by increasing their electromagnetic susceptibility. In this work, radiation from enclosures and apertures is studies and characterized and radiation mitigation techniques are proposed. High-speed circuit radiation within an enclosure leads to cavity resonance that can have critical impact on other electronic components housed within the same enclosure. The amplified electric field in the enclosure can couple to critical circuits leading to either hard or soft failures. One measure to gauge the resonance of an enclosure is through the determination of S-parameters between certain ports connected to the enclosure. In this work, different numerical methods for efficient prediction of S-parameters are proposed and evaluated for their effectiveness and accuracy. Once an efficient procedure is established for calculating S-parameters, novel topological variations within the enclosure can be tested before manufacturing using accurate numerical prototyping. The proposed numerical S-parameters calculation algorithms are validated by comparison to laboratory measurements. Radiation from resonant apertures present in the walls of enclosures represents a second major source for radiation. In this work, a novel analysis of aperture radiation is presented based on the interpretation of the aperture as a transmission line. Once the transmission line analogy is established, a novel aperture resonance mitigation technique is proposed based on the use of material coating that mimics the behavior of matching loads that typically terminate transmission lines. The technique consists of adding resistive sheets in selected places in, or around the aperture. The effectiveness of the proposed method is demonstrated by first using numerical simulation of an aperture present in an infinite perfectly conducting sheet, and then by designing an experiment where the novel technique proposed here is tested on resonant apertures present in a metallic box. Both radiation measurements in an anechoic chamber and S-parameters measurements were conducted to test the validity of the proposed mitigation techniques.