UMD Theses and Dissertations
Permanent URI for this collectionhttp://hdl.handle.net/1903/3
New submissions to the thesis/dissertation collections are added automatically as they are received from the Graduate School. Currently, the Graduate School deposits all theses and dissertations from a given semester after the official graduation date. This means that there may be up to a 4 month delay in the appearance of a given thesis/dissertation in DRUM.
More information is available at Theses and Dissertations at University of Maryland Libraries.
Browse
3 results
Search Results
Item SPECTROSCOPY OF TWO LEVEL DEFECTS & QUASIPARTICLES IN SUPERCONDUCTING RESONATORS(2021) Kohler, Timothy; Osborn, Kevin D; Anlage, Steven; Electrical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)Superconducting films are inherently limited by losses due to two-level system (TLS) defects within the amorphous oxide layers surrounding them and from quasiparticles in the film. In this thesis I will discuss novel theoretical and experimental methods toward understanding superconducting resonator loss from deleterious surface TLS defects as well as a loss transition from non-equilibrium quasiparticles in granular TiN. I will show using finite element solver software that a resonator with submicron linewidth and linespacing can be used to better characterize and simulate surface TLS as part of a circuit QED system. I have observed individual surface TLS and found coupling values in the range of g/2π =50 kHz -280 kHz with a maximum dipole moment pz-max = 4.5 Debye (.93 eÅ). I have found in in simulation of experiment that over 80% of the strongly coupled TLS reside within 50 nm of the corner between the Metal-Substrate (MS) and Substrate-Air (SA) interface. Additionally I have studied a loss transition from non-equilibrium quasiparticles in TiN films. These films exhibit an anomalous loss dependence on substrate treatment and film thickness. The films of interest are ones grown thin on oxidized substrates, which exhibit an order of magnitude decrease in internal quality factor (Qi) relative to either thicker ˝films or films grown without the oxidized substrate. These films additionally exhibit a grain size on average of 7.5 nm, a higher inhomogeneous gap, a transition to lower stress and a preference for the [111] crystal growth. The temperature dependence of the conductivity is fit and a factor of two difference in quasiparticle lifetime is found between the two films where the thinner film has a shorter lifetime. A two gap quasiparticle trapping model is fit to the temperature dependent loss data. The data is consistent with a model where non-equilibrium quasi-particles are trapped in low gapped grains on the inside of the films. From these works and others presented in my thesis the understanding of TLSs on surfaces and non-equilibrium quasiparticles in TiN has improved. This will help illuminate some of the most important absorption mechanisms plaguing superconducting qubits and resonators.Item OPTIMIZATION AND IMPLEMENTATION OF A THERMOACOUSTIC FLASHOVER DETECTOR(2013) Hamburger, Kenneth A; Sunderland, Peter B; Fire Protection Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)The thermoacoustic flashover detector is to be a helmet-mounted device that responds to deteriorating conditions in a compartment fire and produces an audible alarm to alert emergency personnel in time for an escape or change in tactics. An operational prototype device was designed at University of Maryland in 2011, and featured an aluminum, copper, and MACOR tube 178 mm long and 25.4 mm in diameter. The prototype was powered by an external heat band, which provided 44 watts of power at 308 deg C. Optimization of the prototype is conducted across several parameters including power consumption and temperature gradient. To that end, two scaled-down models of diameters 22 mm and 17 mm are constructed, both of which fail to produce sustained sound. Adding water to the device reduces the onset power consumption to 22 watts and the maximum temperature to 285 deg C, which represents the most efficient prototype of the device. A system of radiant heat collector panels and copper-water heat pipes is designed to replace the external heat band as a power source. A heat transfer analysis is conducted to determine the necessary size of the collector panels for proper activation, as well as the response time of the system. Total required surface area will depend on future design parameters, but reasonable estimates suggest that it will be between 0.02-0.03 sq meters. An acoustic analysis of the optimized device is conducted, revealing a fundamental frequency of 500Hz at 101 dB.Item LEAD ZIRCONATE TITANATE THIN FILMS FOR PIEZOELECTRIC ACTUATION AND SENSING OF MEMS RESONATORS(2005-12-07) Piekarski, Brett; DeVoe, Donald; Mechanical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)This research is focused on examining the potential benefits and limitations of applying sol-gel lead zirconate titanate (PZT) piezoelectric thin films to on-chip piezoelectrically driven RF microelectromechanical system (MEMS) resonators in the low frequency (LF) to very high frequency (VHF) frequency range. MEMS fabrication methods are presented for fabricating PZT-based MEMS resonator structures along with investigations into the resultant thin film residual stresses and material properties, and their impact on resonator frequency, beam curvature, and resonant mode shape. The PZT, silicon dioxide (SiO2), platinum (Pt), and silicon nitride (Si3N4) thin film material properties are characterized and validated by wafer bow, cantilever resonance, cantilever thermal-induced tip deflection and finite element modeling (FEM) techniques. The performance of the fabricated PZT-based MEMS resonators are presented and compared to previously demonstrated zinc oxide (ZnO) based resonators as well as to electrostatically based MEMS resonator designs. Resonators with frequency response peaks of greater than 25 dB, quality factors up to 4700, and resonant frequencies up to 10 MHz are demonstrated along with a discussion of their advantages and disadvantages for use as MEMS resonators. Nonlinear resonator response is also investigated in relation to the onset of classic Duffing behavior, beam buckling and mode coupling. Fabrication techniques, operating conditions, and design rules are presented to minimize or eliminate nonlinear resonator response.