Theses and Dissertations from UMD
Permanent URI for this communityhttp://hdl.handle.net/1903/2
New submissions to the thesis/dissertation collections are added automatically as they are received from the Graduate School. Currently, the Graduate School deposits all theses and dissertations from a given semester after the official graduation date. This means that there may be up to a 4 month delay in the appearance of a give thesis/dissertation in DRUM
More information is available at Theses and Dissertations at University of Maryland Libraries.
Browse
2 results
Search Results
Item Miniaturized Power Electronic Interfaces for Ultra-compact Electromechanical Systems(2015) Tang, Yichao; Khaligh, Alireza; Electrical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)Advanced and ultra-compact electromechanical (EM) systems, such as kinetic energy harvesting and microrobotic systems are deemed as enabling solutions to provide efficient energy conversion. One of the most critical challenges in such systems is to develop tiny power electronic interfaces (PEIs) capable of addressing power conditioning between EM devices and energy storage units. This dissertation presents technologies and topological solutions toward fabricating miniaturized PEIs to efficiently regulate erratic power/voltage for kinetic energy harvesting and drive high-voltage actuators for microrobotic systems. High-frequency resonant-switching topologies are introduced as power stages of PEIs that allow small footprint of the circuit without suffering from switching losses. Two types of bridgeless resonant ac-dc converters are first introduced and developed to efficiently convert arbitrary input voltages into a regulated dc output voltage. The proposed topologies provide direct ac-dc power conversion with less number of components, in comparison to other resonant topologies. A 5-mm×6-mm, 100-mg, 2-MHz and 650-mW prototype is fabricated for validation of capability of converting very-low ac voltages into a relatively higher voltage. A resonant gate drive circuit is designed and utilized to further reduce gating losses under high-frequency switching and light-load condition. The closed-loop efficiency reaches higher than 70% across wide range of input voltages and output powers. In a multi-channel energy harvesting system, a multi-input bridgeless resonant ac-dc converter is developed to achieve ac-dc conversion, step up voltage and match optimal impedance. Alternating voltage of each energy harvesting channel is stepped up through the switching LC network and then rectified by a freewheeling diode. The optimal electrical impedance can be adjusted through resonance impedance matching and pulse-frequency-modulation (PFM) control. In addition, a six-input standalone prototype is fabricated to address power conditioning for a six-channel wind panel. Furthermore, the concepts of miniaturization are incorporated in the context of microrobots. In a mobile microrobotic system, conventional bulky power supplies and electronics used to drive electroactive polymer (EAP) actuators are not practical as on-board energy sources for microrobots. A bidirectional single-stage resonant dc-dc step-up converter is introduced and developed to efficiently drive high-voltage EAP actuators. The converter utilizes resonant capacitors and a coupled-inductor as a soft-switched LC network to step up low input voltages. The circuit is capable of generating explicit high-voltage actuation signals, with capability of recovering unused energy from EAP actuators. A 4-mm × 8-mm, 100-mg and 600-mW prototype has been designed and fabricated to drive an in-plane gap-closing electrostatic inchworm motor. Experimental validations have been carried out to verify the circuit’s ability to step up voltage from 2 V to 100 V and generate two 1-kHz, 100-V driving voltages at 2-nF capacitive loads.Item Silicon and Polymer Components for Microrobots(2013) Gerratt, Aaron; Bergbreiter, Sarah; Mechanical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)This dissertation presents the characterization and implementation of the first microfabrication process to incorporate high aspect ratio compliant polymer structures in-plane with traditional silicon microelectromechanical systems (MEMS). This discussion begins with in situ mechanical characterization of microscale polymer springs using silicon-on-insulator-MEMS (SOI-MEMS). The analysis compares microscale samples that were tested on-chip with macroscale samples tested using a dynamic mechanical analyzer. The results describe the effect of the processing steps on the polymer during fabrication and help to guide the design of mechanisms using polymers. Characterization of the dielectric breakdown of polymer thin films with thicknesses from 2 to 14 μm between silicon electrodes was also performed. The results demonstrate that there is a strong dependence of the breakdown field on both the electrode gap and shape. The breakdown fields ranged from 250 V/μm to 635 V/μm, depending on the electrode geometry and gap, approaching 10x the breakdown fields for air gaps of the same size. These materials were then used to create compliant all-polymer thermal and electrostatic microactuators. All-polymer thermal actuators demonstrated displacements as large at 100 μm and forces as high as 55 μN. A 1 mm long electrostatic dielectric elastomer actuator demonstrated a tip displacement as high as 350 μm at 1.1 kV with a electrical power consumption of 11μW. The actuators are fabricated with elastomeric materials, so they are very robust and can undergo large strains in both tension and bending and still operate once released. Finally, the compliant polymer and silicon actuators were combined in an actuated bio-inspired system. Small insects and other animals use a multitude of materials to realize specific functions, including locomotion. By incorporating compliant elastomer structures in-plane with traditional silicon actuators, compact energy storage systems based on elastomer springs for small jumping robots were demonstrated. Results include a 4 mm x 4 mm jumping mechanism that has reached heights of 32 cm, 80x its own height, and an on-chip actuated mechanism that has been used to propel a 1.4mg projectile over 7 cm.