Theses and Dissertations from UMD
Permanent URI for this communityhttp://hdl.handle.net/1903/2
New submissions to the thesis/dissertation collections are added automatically as they are received from the Graduate School. Currently, the Graduate School deposits all theses and dissertations from a given semester after the official graduation date. This means that there may be up to a 4 month delay in the appearance of a give thesis/dissertation in DRUM
More information is available at Theses and Dissertations at University of Maryland Libraries.
Browse
6 results
Search Results
Item Cooling and Stabilization of Graphene Nanoplatelets in High Vacuum(2015) Nagornykh, Pavel; Kane, Bruce E; Physics; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)The study of 2D materials is a rapidly growing area of research, where the ability to isolate and probe an individual single-layer specimen is of high importance. The levitation approach serves as a natural solution for this problem and can be used in ways complementary to the standard techniques. Experiments, including study of properties at high or close to melting temperatures, stretching, folding, vibration and functionalization, can be conducted on levitated 2D materials. As a first step towards realization of all these ideas, one needs to develop and test a system allowing for control over the thermal state and orientation of mono-layer flakes. In this thesis, I present the results of implementation of the parametric feedback cooling scheme in a quadrupole ion trap for stabilization and cooling of graphene nanopletelets. I have tested and showed that the feedback allows to stabilize levitated graphene nanoplatelets in high vacuum conditions (<1 microTorr) to have trapped life times longer than a week. Cooling of the center of mass motion to temperatures below 20 K for all translational degrees of freedom was observed. I have also studied the coupling of DC patch potentials, which were found to be present in the high vacuum chamber. Their effect on cooling was studied and the protocol for minimizing the noise coupling created by the DC fields was designed. We have shown that by varying DC voltages on a set of auxiliary DC electrodes, placed near the trap, one can balance out the DC fields and achieve the lowest cooling temperature. The settings corresponding to this temperature were measured to have a slow drift in time. Ability to tune the settings to balance this drift without breaking the vacuum was studied and found to be a viable solution for the drift cancellation. In addition, our effort in characterization of the flakes is presented. It was shown that the flake discharge quantization observed during the initial pumping down of the high vacuum chamber allows to extract absolute values of flake mass and charge. I also mention the issues experienced with estimation of the shape of the flake, as well as its temperature based on an equipartition theorem. Finally, I discuss the preliminary data on the precession and reorientation of the flakes in the presence of circularly polarized light (CPL) and DC stray fields. The dependence of flake orientation on the offset from the nulling settings is observed and is explained in terms of basic model of a solid charged disk in the presence of two torques created by CPL and DC stray fields.Item Experimental Study of Hybrid Cooled Heat Exchanger(2011) Tsao, Han-Chuan; Radermacher, Reinhard; Mechanical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)A test system for a hybrid cooled heat exchanger was designed, and the test facility was constructed based on ASHRAE Standard 41.2-1987. A conventional air-cooled tube-fin heat exchanger was tested with and without application of wetting water. The baseline tests were conducted to investigate the heat exchanger performance improvement by applying evaporative cooling technology. The heat exchanger capacity and air side pressure drop were measured while varying operating conditions and heat exchanger inclination angles. The results show the heat exchanger capacity increased by 170% with application of the hybrid cooling technology, but the air side pressure drop increased by 130%. Additional research investigating air fan power was also conducted, which increased 120% from the dry condition to the hybrid cooled condition. In summary, the potential for improving the heat exchanger performance by applying hybrid cooling is shown in this research.Item Development of an Experiment for Measuring Film Cooling Performance in Supersonic Flows(2011) Maqbool, Daanish; Cadou, Christopher P; Aerospace Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)This thesis describes the development of an experiment for acquiring supersonic film cooling performance data in canonical configurations suitable for code validation. A methodology for selecting appropriate experimental conditions is developed and used to select test conditions in the UMD atmospheric pressure wind tunnel that are relevant to film cooling conditions encountered in the J-2X rocket engine. A new technique for inferring wall heat flux with 10% uncertainty from temperature-time histories of embedded sensors is developed and implemented. Preliminary heat flux measurements on the uncooled upper wall and on the lower wall with the film cooling flow turned off suggest that RANS solvers using Menter's SST model are able to predict heat flux within 15% in the far-field (> 10 injection slot heights) but are very inaccurate in the near-field. However, more experiments are needed to confirm this finding. Preliminary Schlieren images showing the shear layer growth rate are also presented.Item PERFORMANCE OF A MICROCHANNEL-THERMOELECTRIC POWER GENERATOR WITH ALUMINA-IN-WATER NANOFLUIDS AS COOLANTS(2010) Ahuja, Herwin Singh; Yang, Bao; Mechanical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)In the past two decades, the rapid advancement of military aircraft in terms of performance and power consumption in order to accomplish evermore demanding missions has introduced new challenges, namely, having to conserve of non-renewable petroleum, minimize carbon emissions, and accomplish more mission per unit energy. This thesis describes the work done to evaluate the performance of a renewable-energy device termed the microchannel-thermoelectric power generator (MC-TEPG), which uses alumina-in-water nanofluids as coolants, that is intended to replace or supplement current non-renewable power supplies such as battery packs in order to contribute to overcoming the abovementioned challenges. The MC-TEPG recovers waste heat internally generated by motors of military aircraft and converts it to usable electric power via the Seebeck effect. This thesis studies nanofluid flow and heat transfer in the MC-TEPG microchannels, and thermoelectric power generation under varying conditions. Current results show MC-TEPG feasibility and suggest future promise.Item On-Chip Thermoelectric Cooling of Semiconductor Hot Spot(2007-08-28) Wang, Peng; Bar-Cohen, Avram; Mechanical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)The Moore's Law progression in semiconductor technology, including shrinking feature size, increasing transistor density, and faster circuit speeds, is leading to increasing total power dissipations and heat fluxes on silicon chip. Moreover, in recent years, increasing performance has resulted in greater non-uniformity of on-chip power dissipation, creating microscale hot spots that can significantly degrade the processor performance and reliability. Application of conventional thermal packaging technology, developed to provide uniform chip cooling, to such chip designs results in lower allowable chip power dissipation or overcooling of large areas of the chip. Consequently, novel thermoelectric cooler (TEC) has been proposed recently for on-chip hot spot cooling because of its unique ability to selectively cool down the localized microscale hot spot. In this dissertation the potential application of thermoelectric coolers to suppress on-chip hotspots is explored using analytical modeling, numerical simulation, and experimental techniques. Single-crystal silicon is proposed as a potential thermoelectric material due to its high Seebeck coefficient and its thermoelectric cooling performance is investigated using device-level analytical modeling. Integrated on silicon chip as an integral, on-chip thermoelectric cooler, silicon microcooler can effectively reduce the hotspot temperature and its effectiveness is investigated using analytical modeling and numerical simulation, and found to be dependent of doping concentration in silicon, electric contact resistance, hotspot size, hotspot heat flux, die thickness and microcooler size. The other novel on-chip hotspot cooling solution developed in this dissertation is to use a mini-contact enhanced TEC, where the mini-contact pad connects the silicon chip and the TEC to concentrate the thermoelectric cooling power onto a spot of top surface of the silicon chip and therefore significantly improve the hotspot cooling performance. Numerical simulation shows hotspot cooling is determined by thermal contact resistance, thermoelectric element thickness, chip thickness, etc. Package-level experiment demonstrates that spot cooling performance of such mini-contact enhanced TEC can be improved by about 100%.Item Near quantum limited measurement in nanoelectromechanical systems(2006-09-07) Naik, Akshay; Schwab, Keith; Electrical Engineering; Digital Repository at the University of Maryland; University of Maryland (College Park, Md.)Nanoelectromechanical systems have many potential applications in nanoelectronics as well as in fundamental studies of quantum mechanics in mesoscopic systems. Nanoelectromechanical systems have been touted as an extension of microelectromechanical systems which would operate at higher frequencies and consume far less power due their higher quality factors. Since these systems can be cooled close to their ground states with existing cryogenic techniques, they are useful tools to study the quantum effects like backaction, coherent states and superposition in mesoscopic mechanical systems. Also there have been proposals to use these systems as qubits and buses in quantum computing. In this thesis I discuss the effects of the backaction of a superconducting single electron transistor that measures the position of a radio frequency nanomechanical resonator. One of the novel effects of this backaction is the cooling of the nanomechanical resonator. The fact that a system can be cooled by merely coupling it to noisy non-equilibrium device is a counterintuitive phenomenon. Although backaction effects have been used to produce ultra-cold atoms, our results are the first demonstration of this cooling effect in a mesoscopic system. For a linear continuous position detection scheme, quantum mechanics places a lower limit on the product of position shot noise, Sx, and the backaction force noise, SF, which is given by, (S_x S_F)^(1/2)> hbar/2 As part of this work we demonstrate that our detection scheme is only 15 times away from this limit and only 4 times away from quantum limit for position sensitivity.