Show simple item record

dc.contributor.advisorDeVoe, Don Len_US
dc.contributor.authorBarham, Oliver M.en_US
dc.date.accessioned2017-09-13T05:39:45Z
dc.date.available2017-09-13T05:39:45Z
dc.date.issued2017en_US
dc.identifierdoi:10.13016/M2222R63Z
dc.identifier.urihttp://hdl.handle.net/1903/19842
dc.description.abstractPiezoelectric voltage transformers (PTs) can be used to transform an input voltage into a different, required output voltage needed in electronic and electro- mechanical systems, among other varied uses. On the macro scale, they have been commercialized in electronics powering consumer laptop liquid crystal displays, and compete with an older, more prevalent technology, inductive electromagnetic volt- age transformers (EMTs). The present work investigates PTs on smaller size scales that are currently in the academic research sphere, with an eye towards applications including micro-robotics and other small-scale electronic and electromechanical sys- tems. PTs and EMTs are compared on the basis of power and energy density, with PTs trending towards higher values of power and energy density, comparatively, indicating their suitability for small-scale systems. Among PT topologies, bulk disc-type PTs, operating in their fundamental radial extension mode, and free-free beam PTs, operating in their fundamental length extensional mode, are good can- didates for microfabrication and are considered here. Analytical modeling based on the Extended Hamilton Method is used to predict device performance and integrate mechanical tethering as a boundary condition. This model differs from previous PT models in that the electric enthalpy is used to derive constituent equations of motion with Hamilton’s Method, and therefore this approach is also more generally applica- ble to other piezoelectric systems outside of the present work. Prototype devices are microfabricated using a two mask process consisting of traditional photolithography combined with micropowder blasting, and are tested with various output electri- cal loads. 4mm diameter tethered disc PTs on the order of .002cm^3 , two orders smaller than the bulk PT literature, had the following performance: a prototype with electrode area ratio (input area / output area) = 1 had peak gain of 2.3 (± 0.1), efficiency of 33 (± 0.1)% and output power density of 51.3 (± 4.0)W cm^-3 (for output power of 80 (± 6)mW) at 1MΩ load, for an input voltage range of 3V-6V (± one standard deviation). The gain results are similar to those of several much larger bulk devices in the literature, but the efficiencies of the present devices are lower. Rectangular topology, free-free beam devices were also microfabricated across 3 or- ders of scale by volume, with the smallest device on the order of .00002cm^3 . These devices exhibited higher quality factors and efficiencies, in some cases, compared to circular devices, but lower peak gain (by roughly 1/2 ). Limitations of the microfab- rication process are determined, and future work is proposed. Overall, the devices fabricated in the present work show promise for integration into small-scale engi- neered systems, but improvements can be made in efficiency, and potentially voltage gain, depending on the applicationen_US
dc.language.isoenen_US
dc.titleMicrofabricated Bulk Piezoelectric Transformersen_US
dc.typeDissertationen_US
dc.contributor.publisherDigital Repository at the University of Marylanden_US
dc.contributor.publisherUniversity of Maryland (College Park, Md.)en_US
dc.contributor.departmentMechanical Engineeringen_US
dc.subject.pqcontrolledMechanicsen_US
dc.subject.pqcontrolledMaterials Scienceen_US
dc.subject.pqcontrolledElectrical engineeringen_US
dc.subject.pquncontrolledHamiltonen_US
dc.subject.pquncontrolledmicrofabricationen_US
dc.subject.pquncontrolledpiezoen_US
dc.subject.pquncontrolledpiezoelectricen_US
dc.subject.pquncontrolledpzten_US
dc.subject.pquncontrolledtransformeren_US


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record